G1 setup problem

This option will restore the original factory system defaults. It is safe to turn off the computer only after exiting the F10 Setup screen.

Computer Setup—File note: Support for specific Computer Setup options may vary depending on the hardware configuration. Save current settings as Default. Applies the currently selected default settings and clears any established passwords. Saves changes to system configuration or default settings and exits Computer Setup. Computer Setup—Storage note: Support for specific Computer Setup options may vary depending on the hardware configuration.

When a device is selected, detailed information and options are displayed. The following options may be presented:. Lets you select the translation mode to be used for the device. Logical cylinders may not exceed The number of heads may not exceed The number of sectors per track may not exceed If the selected translation mode is not compatible with the translation mode that was active when the disk was partitioned and formatted, the data on the disk will be inaccessible.

Allows you to choose how the SATA controller and devices are accessed by the operating system. IDE - This is the most backwards-compatible setting of the three options. Operating systems usually do not require additional driver support in IDE mode. Default is enabled. Each device on the list may be individually excluded from or included for consideration as a bootable operating system source. Legacy Boot Sources: Specify the order in which legacy boot sources such as a network interface card, internal hard drive, USB optical drive, or internal optical drive are checked for a bootable operating system image.

Specify the order of attached hard drives. The first hard drive in the order will have priority in the boot sequence and will be recognized as drive C if any devices are attached. To remove the device from consideration as a bootable device, press F5.

To boot one time from a device other than the default device specified in Boot Order, restart the computer and press Esc to access the boot menu and then F9 Boot Order , or only F9 skipping the boot menu when the monitor light turns green. After POST is completed, a list of bootable devices is displayed. Use the arrow keys to select the preferred bootable device and press Enter.

The computer then boots from the selected non-default device for this one time. Computer setup - Security note: Support for specific Computer Setup options may vary depending on the hardware configuration.

Allows to set and enable a power-on password. The power-on password prompt appears after a power cycle or reboot. If the user does not enter the correct power-on password, the unit will not boot. Password Options This selection appears only if a power-on password or setup password is set. Lock Legacy Resources determines whether or not Windows Device Manager is allowed to change resource settings for serial and parallel ports.

Stringent security enabling the stringent password disables the ability to reset the password by moving the jumper on the system board. Default is disabled. If you lose or forget the password, the system board must be replaced.

This scenario is not covered under warranty. To prevent the computer from becoming permanently unusable, record your configured setup password or power-on password in a safe place away from your computer. Without these passwords, the computer cannot be unlocked. Setup Browse Mode appears if a setup password is set allows viewing, but not changing, the F10 Setup Options without entering setup password.

Feature available on NIC models only; the network controller must be either a PCI expansion card or embedded on the system board. Asset tag byte identifier , a property identification number assigned by the company to the computer. The UUID can only be updated if the current chassis serial number is invalid. These ID numbers are normally set in the factory and are used to uniquely identify the system. The MBR contains information needed to successfully boot from a disk and to access the data stored on the disk.

The default is 10 percent. Increasing the concurrent marking threads will make garbage collection run fast. Force G1 to start marking phase earlier. Default value is Even though there is enough space in a heap, a Full GC can also occur due to lack of a contiguous set of space. When you try to increase this value, GC will be triggered earlier, preventing the Evacuation pauses.

The default value is Reducing the value will start the marking cycle earlier. If the problem persists you may consider increasing JVM heap size i.

You can fix this problem through following solutions: a. This frequency can be configured using the following JVM arguments when you launch the application: -Dsun. Conclusion We hope you find this article useful. Share this: Tweet. Like this: Like Loading GCeasy Team Author archive. Leave a Reply Cancel reply. Loading Comments Email Required Name Required Website. Is there a docking station involved? First thing I tried. Always good to check tho! She's the kind of user who would own up to spilling something on it.

DavidLoewen wrote: I have had weird issues with some displayport adapters in the past. I wasn't aware there were active and non-active cables. After some research, I think I have tested both active and non-active. Thanks for this info! Pure Capsaicin. EzrasMonkey wrote Also checked the drivers on HPs website Which model HP laptop? Did a Microsoft driver update get surreptitiously installed?

Mattias Jan 26, at UTC. Chris Feb 1, at UTC. This topic has been locked by an administrator and is no longer open for commenting. We are seeing the internet drop multiple times a day. Request if you can suggest a solution for the same. Thanks for asking, while as mentioned above that this model is specially designed for the local ISPs, so the firmware is customized, I'm afraid we cannot provide you further suggestions.

Generally, if the connection between the extender and the main network is not stable, it is mainly caused by the wireless channel switching on the main router, you may check if you can fix the wireless channel on the router, then reboot the ECG1 to rebuild the connection. Meanwhile, the distance and interference between the two can make big difference, so it is suggested to put the ECG1 in the location where you can get at least bars signal from the main.

To be honest, I don't get the excuse that the firmware is customised. My ISP doesn't have a software development department, they're not able to fix those bugs. You should take that report and release fixed FW version to ISPs and probably also to users who get those devices from resellers. What's more, googling that model shows TP-Link sites on top, however, when we report bugs to you, the only answer is "go to your ISP".

You should at least provide a list of available firmwares so I would have information whether my ISP can provide me an update or not. Now I feel like I bought an overpaid chinese router from Aliexpress, without any support and with a poor firmware.

We are sorry to disappoint you, while we cannot help you, as you can see this model is only listed for the Service Providers, so the firmware is customized, we cannot help you further:. If you do buy it from the reseller Aliexpress , you may check this with the local tech support team and see if they have any other suggestions for you.